Bently Nevada 3300/16-14-01-03-00-00-00 XY/GAP Dual Vibration Monitor

Description:

The 3300/16-14-01-03-00-00-00 3300/16 XY/Gap Dual Vibration Monitor continuously measures and monitors:

• Radial vibration (two independent channels).
• Average shaft position (gap).
• Inputs from two proximity probes/Proximitor® systems.

It is designed as an upgrade from the 3300/15 Dual Radial Vibration Monitor, offering radial position gap alarms for enhanced monitoring.

---

Specifications:

Signal Inputs:

• Accepts one or two proximity probe signals.
• Input Impedance: 10 kΩ.
• Sensitivity Options:
  • 100 mV/mil (4 V/mm).
  • 200 mV/mil (8 V/mm) (user-programmable).

Power Consumption:

• Nominal: 2 watts.

Signal Conditioning:

• Accuracy at +25°C (+77°F):

  • ±0.33% of full scale (typical).
  • ±1% maximum.
  • ±2% maximum with 2X Trip Multiply.
  • ±3% maximum with 3X Trip Multiply.

• Frequency Response (User-Programmable):

  • 4 Hz to 4,000 Hz (240 to 240,000 cpm).
  • 1 Hz to 600 Hz (60 to 36,000 cpm) (for low-speed applications, not recommended for rapid startups and coastdowns exceeding 1,000 rpm/s).

---

Recorder Outputs:

• User-programmable options:

  • +4 to +20 mA.
  • 0 to -10 VDC.
  • +1 to +5 VDC.

• Output Impedance (Voltage Outputs): 100 Ω (Minimum load resistance: 10 kΩ).

• Voltage Compliance (Current Outputs): 0 to +12 VDC (Load resistance: 0 to 600 Ω for +4 to +20 mA option).

• Recorder Accuracy at +25°C (+77°F):

  • +4 to +20 mA: ±0.7% of signal, ±0.09 mA offset.
  • +1 to +5 VDC: ±1.1% of signal, ±10 mV offset.
  • 0 to -10 VDC: ±1.1% of signal, ±15 mV offset.

---

Buffered Transducer Outputs:

• One coaxial connector per channel on the front panel.
• One terminal connection per channel on the rear panel.
• Short-circuit protected.

Transducer Supply Voltage:

• User-programmable:
  • -24 VDC.
  • -18 VDC.
  • (Current limited on individual monitor circuit board).

Note: If using 3000 series transducers in a system with 3300 and/or 7200 series transducers, consult the sales representative.

---

Alarm Setpoints:

• Alert & Danger Setpoints for vibration.
• Gap Alert Setpoints for both channels.

Resolution:

• Digital adjustment from 0 to 100% of full scale (LCD resolution: ±1.6%).
• Repeatability: ±0.39% of full scale.
• Gap Alarm Time Delay: 6 seconds.

---

Relays:

• One alarm relay module can be installed per monitor.
• At least one relay module is required per 3300 System.

---

Displays:

• Non-multiplexing, vertical bargraph LCD (individual 63-segment LCD per channel).
• Probe Gap Display: Third center scale.
• Error Code & Adjust Mode Display.

Resolution:

• ±1.6% of monitor full scale.

Size:

• 3.25 inches (83 mm) vertical dimension.

---

LED Indicators:

• OK (Green LED):

  • ON: Normal condition.
  • OFF: NOT OK condition or channel bypassed.
  • Flashing at 1 Hz: Channel was NOT OK but is now OK.
  • Flashing at 5 Hz: Error codes stored in memory.

• Alarm (Red LEDs):

  • Two per channel (indicating Alert and Danger).
  • Flashing: Indicates First Out status.

• Bypass (Red LEDs):

  • Indicate Danger Bypass or Rack/Channel Bypass.
  • Flashing: Monitor is in Trip Multiply Mode.

---

Environmental Limits:

• Operating Temperature: 0°C to +65°C (32°F to 150°F).
• Storage Temperature: -40°C to +85°C (-40°F to 185°F).
• Relative Humidity: Up to 95% non-condensing.

---

Physical & Installation:

• Rack Space Requirement:
  • One rack position (any except 1 and 2, reserved for Power Supply & System Monitor).
• Weight: 1 kg (2.2 lbs).

---

Ordering Information:

Part Number Format:

3300/16 – AXX – BXX – CXX – DXX – EXX – FXX

Part Number:

3300/16-14-01-03-00-00-00

Option Descriptions:

A: Full-Scale Range Option

• 1 4: 0-400 µm pp.

B: Transducer Input Option

• 0 1: Supports 3300 XL 8mm, 7200 5mm & 8mm Proximitor Sensors (200 mV/mil).

Note: For 3000 series transducers, consult a sales representative.

C: Alarm Relay Option

• 0 3: Quad Relay (Epoxy-sealed only).

Notes:

1. AND voting logic is unavailable with Quad Relays.
2. At least one relay module per 3300 System is required.
3. Quad Relays cannot be used with Internal Safety Barriers.

D: Agency Approval Option

• 0 0: Not required.

E: Safety Barrier Option

• 0 0: None.

F: Trip Multiply Option

• 0 0: None.

---

Contact Us

• Phone: +86-15915488782
• Email: [email protected]
• WhatsApp: +8615915488782
• Business Hours: 24/7 service
• Address: Unit 601, Powerlong International Center, No. 1599 Luling Road, Siming District, Xiamen City, Fujian, China

Let us help you find the automation parts you need with reliable quality and dedicated support!